CONEXANT USB CX93010 ACF MODEM DRIVER FOR WINDOWS DOWNLOAD
MOH with indefinite timeout Granted. Reported when transmission has been terminated for the specified amount of time. In Framed sub-Mode, modem transmits abort on underrun in middle of frame default. Selects asynchronous operation in normal mode speed buffering. Send a break in sequence with received data to DTE. Fcl – Carrier Loss Timeout ms.
|Date Added:||9 March 2013|
|File Size:||14.14 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
A fixed value of zero is used and reported. Renegotiate rate up one speed used for diagnostic purpose only. Syntax And Procedures The termination cobexant may not appear in the body. Reporting Current or Selected Value Command: The use of conexant usb cx93010 acf modem event reporting for Stuttered Dial tone is for further study.
Indicates loss in dB caused by digital pads. S19 is supported for backwards conexant usb cx93010 acf modem only. DSR will become active after answer tone has been detected and inactive after the carrier has been lost. Don’t show me this message again. The modem has connected to the line at bps and carrier reporting is enabled.
MOH with 6 minute timeout Granted. Initiates local analog loopback, V. The modem cannot process AT commands and cannot detect and qualify ring signals. Page 58 Use “H” to abort the dial in progress, and go back on-hook.
CONEXANT CX REFERENCE MANUAL Pdf Download.
Fax Class 1 Answering Sequenc Play silence with a duration of ms. Decimal number which specifies the initial requested mode of operation when the modem is operating as the originator.
Page This command causes the modem to initialize all voice parameters to their default values. In non-error correction mode direct, the break length is passed; in non- error correction mode normal and in error correction mode, a ms break is passed. Disables result codes to the DTE.
Conexant usb cx93010 acf modem of Go.
MNP is in use. Reporting Current or Selected Values Command: S40 indicates the status of command options. The modem has connected to the line in V. Scid – Snooping Cid type Ii 1. Page 92 Send a break immediately to DTE. This manual also for: Fae – Auto Answer Enable Reported when transmission has been terminated for the specified moedm of time. Use conexant usb cx93010 acf modem to abort the dial in conexant usb cx93010 acf modem, and go back on-hook.
Decimal number corresponding to the selected option. Page 2 Conexant may make changes to this document at any time, without notice. Some countries prevent changing dialing modes after the first digit is dialed. Ussb to asynchronous operation only.
RATOC Windows 7動作確認状況
Page The modem has connected to the line at bps and carrier reporting is enabled. Number of retrains initiated by the movem. Basic Syntax Commands Conexant usb cx93010 acf modem the “?
Result Codes in V. Page The modem has connected to the line in V. Send a break in sequence with received data to DTE.
Conexant CX93010 Reference Manual
Page 42 The value b is written to S22 bits 6, 5, and 4, respectively. Parameters applicable to each command are listed with the command description. If multiple values are to be reported with the cx993010 code, the form is: Number of retrains conexat by the remote modem.
Page 80 Alphanumeric code corresponding to the reported carrier. For W-class models, the modem will return on-hook after a period of time determined by S7. Upon connection, the modem reports the DCE speed e. Commands and responses are in conexant usb cx93010 acf modem case e.
Line In Use ac bit 0 and extension pick-up is bit 1. H – Disconnect hang-up If on-hook, the modem will go off-hook and enter command mode. Reporting Current or Selected Values: The characters transmitted for the header and trailer are determined by the V command setting. Conexant usb cx93010 acf modem asynchronous operation in normal mode speed buffering.
Reported if loss-of-carrier is detected. A 0 indicates not supported.